zalman T3 Plus Matx Mini Tower Computer Case
Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.
- To ensure safe and easy installation, please read the following precautions.
- Product design and specifications may be revised to improve quality and performance without notice.
Contents
hide
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
Model | T3 PLUS | |
Case Form Factor | mATX Mini-Tower | |
Dimensions | 355 x 206 x 422(H)mm | |
Weight | 3.6kg | |
Case Materials | Plastic, Steel, Tempered Glass | |
Motherboard Support | mATX / Mini-ITX | |
Maximum VGA Length | 290mm | |
Maximum CPU Cooler Height | 150mm | |
Maximum PSU Length | 140mm | |
PCI Expansion Slots | 4 | |
Drive Bays | 1 x Combo (3.5″ or 2.5′; 1 x 3.5″), 1 x SSD (2.5″) | |
Fan Support | Top | 2 x 120mm |
Front | 3 x 120mm/2 x 140mm | |
Rear | 1 x 120mm | |
Bottom | 2 x 120mm | |
Fan(s) Included | Front | 1 x 120mm |
Rear | 1 x 120mm | |
Radiator Support | Front | 1 x 120mm |
I/O Ports | 1 x Headphones, 1 x MIC, 2 x USB2.0, 1 x USB3.0, Reset Button, Power Button |
Accessories Component
I/O Ports
Removing the side panels
- Tempered Glass
- Steel Panel
Removing the front panel
Mounting the motherboard
Motherboard size
Mounting PCI-E(VGA) card
Mounting the 2.5″ SSD
Mounting the 3.5″ and 2.5″ SSD / HDD
Mounting the PSU
Mounting the radiator
- Mounting the front radiator
- 1 x 120mm
- 1 x 120mm
Mounting the fans
- Mounting the top fans
- 2 x 120mm
- 2 x 120mm
- Mounting the front fans
- 3 x 120mm, 2 x 140mm
- 3 x 120mm, 2 x 140mm
- Mounting the rear/bottom fan
- 1 x 120mm/2x120mm
- 1 x 120mm/2x120mm
Documents / Resources
zalman T3 Plus Matx Mini Tower Computer Case [pdf] User Manual T3 Plus Matx Mini Tower Computer Case, T3 Plus, Matx Mini Tower Computer Case, Mini Tower Computer Case, Tower Computer Case, Computer Case, Case |