Key features
The recently tested SilentiumPC Fera 3 cooler did not do badly in our tests, but it was a bit noisy. Today we will look at a cooler from the same family, i.e. SilentiumPC Fera 3 RGB. As the name suggests, this cooler offers RGB backlighting. In addition, the entire heatsink is a few millimeters lower and a different fan is also used. I just hope that these differences will not have a negative effect under stress tests.
Key features of the cooler
In terms of architecture, the SilentiumPC Fera 3 RGB is very similar to its little brother without RGB. As with the non-RGB variant, the cooler is based on four copper heatpipes intersecting a bundle of aluminum fins. Heatpipes use direct contact with the processor’s heat spreader, which SilentiumPC refers to by the suffix HE (high efficiency) in the full name of the cooler. The entire heatsink is then cooled by a 120 mm fan with RGB LED.
The overall width and depth of the fin bundle remained the same, differing only in the overall height of the cooler by a few millimeters. The Fera 3 RGB thus falls into the category of coolers with a height of less than 150 mm, which increases the number of compatible cases. I myself used it for an SFF PC in the Streacom DA2 case, where it fit like perfectly. Where the Fera 3 RGB also differs from its older type is the design of the upper surface of the cooler. The upper fin and the ends of the heatpipes are covered by a milky white diffuser, under which RGB LEDs are hidden. This diffuser then has a black cover with a cutout of the manufacturer’s logo and several other aesthetic elements that allow the RGB LED to shine through.
The unit is visually very attractive and it is quite a pity that this method of backlighting is not used by more manufacturers. Backlight cables allow serial connection, which eliminates the need for hubs and simplifies cabling. The mounting of the fan is performed in the same way as with the Fera 3, i.e. by means of metal clips, which are slid in the grooves in the fins on the sides of the heatsink.
The cooler accessories are no surprise. Here you will find a universal mounting system for both Intel and AMD processor sockets, as well as another set of clips for the second fan if you would like to use a push-pull configuration. A small package of thermal paste (Pactum PT-2) and a brief user manual with installation instructions are also not missing. In addition, you will find a Nano-reset RGB controller here if you do not want or cannot connect a 4 pin cable from the RGB backlight to your motherboard. You simply connect this controller using a 2-pin cable from the Reset button in your case. The Reset button then switches the RGB backlight modes without any software.
The cooler’s mounting system is identical to the non-backlit version. So all the reservations I mentioned in the review of SilentiumPC Fera 3 still apply. Thus, the absence of integrated screws with a spring to attach the heatsink to the mounting system. The pair of screws used is quite short. It is not so easy to hold the heatsink in position and at the same time tighten the screw, on which you have to apply more pressure to reach the thread at all. Therefore, I still recommend mounting this cooler ideally outside the case with the motherboard in a horizontal position.
Specs of the cooler and fans
SilentiumPC Fera 3 RGB is very similar in size to the non-RGB version, differing only in overall height. The Fera 3 RGB with its height below 150 mm will be compatible with most common ATX cases. And like the non-RGB variant, this cooler offers an offset design. Therefore, there is no conflict with high heatsinks on RAM modules. You can mount the cooler on all motherboards with sockets for current Intel and AMD processors, except, of course, TR4/sTR4 sockets.
Cooler | SilentiumPC Fera 3 | SilentiumPC Fera 3 RGB | |
Noctua U12A | |||
Supported sockets | Podporované patice | Intel LGA 115x, 1200, 20xx; AMD AM4 | Intel 115x, 1200, 20xx; AMD AM4 |
Height | Výška (bez ventilátoru) | 155 mm | 146 mm |
Width | Šířka (bez ventilátoru) | 123 mm | 123 mm |
Depth with fan | Hloubka s ventilátorem | 78 mm | 78 mm |
Weight | Váha (bez ventilátoru) | 610 g | 630 g |
Maximum RAM height | no limit | bez omezení | |
MSRP | Maximální výška RAM | 26 € | 39 € |
Unfortunately, SilentiumPC provides only a minimum of information about the fan used. It is a 120 mm fan with a standard width of 25 mm with PWM regulation. RGB backlighting is provided by a standard 4-pin connector, you will not find any proprietary inconveniences here.
Fan | Sigma Pro 120 PWM | Stella HP RGB 120 PWM | |
Gelid Radiant RGB | |||
Bearing | Ložisko | Hydraulic Bearing | Double Ball Bearing |
Speed range | Výška (bez ventilátoru) | 500–1600 RPM | 500–1600 RPM |
RGB lighting | Maximální průtok vzduchu | N/A | 4-pin (12 V) |